https://warriorplus.com/o2/a/x8g6yk/0 be more attractive: How to Make a Simple Robot With Everyday Supplies

mercredi 12 août 2015

How to Make a Simple Robot With Everyday Supplies

This little robot will add to your collection of cool things to display! These instructions tell you how to build a small robot that lights up its eyes, for an inexpensive, fun showpiece.

Steps

  1. Pick your LEDs and heat shrink. The two LEDs will form the robot's eyes. Optionally, get heat shrink tubing as well for added color. You won’t need more that 5 inches (13cm) of heat shrink for this project.
    Make a Simple Robot With Everyday Supplies Step 1 Version 2.jpg
  2. Clip a piece off of the heat shrink. Cut two small pieces of heat shrink, each about ½ inch (1.25cm) long. This should be small enough that the pins on your LED will poke out after sliding through the heat shrink.
    Make a Simple Robot With Everyday Supplies Step 2 Version 2.jpg
  3. Slide the LED through the heat shrink. If you are using heat shrink, push the LED through until the light-up tip peeks out. Repeat this process for the second LED.
    Make a Simple Robot With Everyday Supplies Step 3 Version 2.jpg
  4. Shrink the heat shrink with a soldering iron. Start up your solder iron and bring it close to the LED and the heat shrink. The heat from the iron should shrink the tube. Hold the LED with pliers to protect your fingers from the heat.
    Make a Simple Robot With Everyday Supplies Step 4 Version 2.jpg
  5. Select the battery pack. Get a battery pack rated of about 3v. This should fit two AA batteries.
    SimpleRobotBatteryPack.jpeg
  6. Solder the LED and resistor to the battery pack. Take some insulated wire with the ends stripped. Solder these components as follows:
    CircuitDiagram.png
    • Solder the negative (black) wire of the battery pack to the short terminal of the LED.
    • Take a 100 ohm resistor (or a resistor close to that range). Without the resistor, the LED with die out.
    • Solder one pin of the resistor to the positive wire of the battery.
    • Solder the other pin of the resistor to the LED's positive terminal.
    • Connect the two positive pins of the two LED's.
    • Connect the two negative pins of the two LED's.
      SolderLED.jpeg
  7. Bend four paperclips into legs. Cut the paperclips such that they look like legs of the robot.
    PaperClipsAfter.jpeg
    PaperClipsBefore.jpeg
  8. Solder on your motor’s wires to the battery holder. Solder the vibrating motor's wires to the positive and the negative wire of the battery holder.
    SimpleRobotSolderMotor.jpeg
  9. Hot glue the motor to the battery holder. Hot glue the motor on top of the battery holder. Attach the battery holder's wires to the motor pins.
    SimpleRobotGlueMotorBattery2.jpeg
    SimpleRobotGlueMotorBattery1.jpeg
  10. Finish your robot. Prop up your robot with the paper clip legs. Put the batteries in and watch your little robot light up and move. Keep it on a flat, smooth surface so it doesn't fall over.
    WikiHowRobot.jpeg

Tips

  • For your safety, wear safety goggles and use a fume extractor while soldering.
  • Add some heat shrink tubing to the legs for extra pizazz.

Warnings

  • Be careful when using a hot-glue gun and soldering iron

Things You'll Need

  • 2 LED crystals
  • 4 Jumbo paperclips
  • Soldering iron
  • 2 AA batteries
  • Battery holder
  • Pager motor (small vibrating motor found in cell-phones)
  • 100Ω resistor

Related wikiHows



source How to of the Day http://ift.tt/1ToCKK7

Aucun commentaire:

Enregistrer un commentaire

https://warriorplus.com/o2/a/x8g6yk/0

How to Start a Text Conversation

You just got someone’s number, but now you’re staring at your phone, wondering what exactly you should text them. We’ve all been there, but...

https://warriorplus.com/o2/a/x8g6yk/0