How to Load 35Mm Film Into a Manual Camera

People take photos in all environments and it is important to make sure you have the right film selected for your lighting conditions and to make sure the film is loaded properly to ensure that your photos come out. This article will prepare you for an outdoor photography setting, using no flash.

EditSteps

1. Decide upon what lighting conditions will be present for desired photography. #*On a sunny day choose a slow film speed 100ISO or 200ISO
   
   
   • Near dawn, dusk, or dark clouds choose a faster speed such as 800ISO
   • If you will be shooting all day or are unsure of the exact light, choose 400ISO
2. Pick-Up your camera and roll of film.
   
   
3. Look to the left of the top of the camera.
   
   
4. Find the circular disc that is on top that has an arrow drawn on the disc.
   
   
5. Look to the left of this circular piece.
   
   
6. Find the small black knob.
   
   
7. Slide the knob towards you and as you do this, pull up on the circular disc.
   
   
8. Pull gently but firmly up on the disc until you hear the back door of the camera pop open.
   
   
   • You have now successfully opened the back of the camera and are ready to load film.
9. If you were unable to open the back door, push the circular disc back down and repeat.
   
   
10. Un-package your roll of film.
    
    
    • There should be roughly an inch of film hanging out of the roll of film. This is called the leader.
    • If there is not a leader, you will need a special tool. Consult your teacher for help.
    • If no teacher is available, use another roll of film.
    • You may assume that the top of the film is the end with the circle protruding from the main cylinder. However, this is not the case; this is actually the bottom.
11. Take the roll of film and lay it on top of the cradle (not in) on the left hand side. Ensure that the flange out of the roll of film that has the leader sticking out is to the right over the back of the camera. (It’s hard to mess this up if the roll of film is oriented properly in the cradle.)
    
    
12. Pull up on the same disc from before as you do this. Push the roll of film down into the cradle.
    
    
13. Next, with the roll of film securely in place, pull the leader across the back of the camera by grabbing the sides of the film so no fingerprints make it on the surface of the film.
    
    
14. Once the film has reached the other side of the camera, you must lock the film into the winding mechanism so that the film will move across the film plane when it is winded after every exposure.
    
    
    • On the back of the camera on the right where the tip of the leader is, you will notice two spindles; one with sprockets and another to hold the tip of the leader.
15. Insert the leader into one of the two slits on the right spindle.
    
    
    • On the top and bottom of the sprocket, (left) spindle are sprockets, and on the top and bottom of the film there are sprocket holes.
16. Line up the sprocket holes on the sprockets.
    
    
17. Holding the film in place on the sprockets and with the leader in a slit on the spindle, with your left hand, find the advancement mechanism which is connected to the right spindle but on top of the camera and spin it out and to the right with your right thumb. If the advancement mechanism does not move out, push down the shutter release, which is the silver button to the top of the advancement mechanism if looking from above.
    
    
    • The spindle will move clockwise, which will appear to be wrong because it takes the film and bends it around the spindle in what looks to be backwards. This however is correct, and the film is wound on the spindle in this manor to ensure it does not slide off.
    • The film should wrap around the spindle and move a short distance, once the advancement mechanism stops release the shutter and you will get another crank out of it.
18. Repeat previous steps three to four times to ensure that the film is firmly connected to the spindle.
    
    
19. Shut the back door.
    
    
20. Repeat two more times.
    
    
    • The numbers on the top of the camera should read anywhere from 0 to 3.
21. Push down the circular disc on the far left that you lifted up originally to load the film.
    
    

EditThings You'll Need

• Camera
• Film, which is 35mm

EditRelated wikiHows

• Use Almost Any 35mm Film Camera
• Create a Panoramic Photo Using Hugin
• Make a Pintoid Camera
• Make a 620 Camera Use 120 Film
• Develop Black and White Film
• Make a 120 Camera Use 620 Film
• Develop Color Film

source How to of the Day http://ift.tt/1oCYKUh