These instructions will guide you in creating a fun dollar origami parrot. Sitting snugly on your finger, this parrot makes for a great gift to kids. Additionally, its monetary value allows for a great tip that sits well on most glasses or bottles at restaurants.
EditSteps
- Begin with creases. Fold and unfold the bill in half lengthwise. Whether you choose the face of the bill or not won't matter for this model.(Creases are simply to guide folds in later step.)
- Create an "X". Fold one of the short edges to meet the length of the bill creating a point as shown in the image. Unfold and repeat on closest corner. The two creases should intersect forming a large "X" on one end of the bill.
- Keep one corner folded. Align the triangle to the back along the edge that overlaps with the bill. Make sure you only have the triangle folded back and you avoid any additional paper. Once unfolded you should see a perfect square on one end of the bill.
- Unfold completely. Align the short edge with the middle crease. Repeat this on both sides with adjacent edges to corresponding creases. Choose one of the diagonals and stick with it for your folds.
- Prepare for fourth crease. Fold the "square" back. This is best done by refolding a corner and then realigning it to the overlapping edge of the triangle.
- Create fourth crease by aligning the folded edge to the middle crease you have chosen for the other edges. This completes a diamond shape where the "X" used to be. Unfold.
- Collapse the model. Fold the outside edges to the center. The edges will line up to create a diamond along with a left over flap. This is where the creases really come into play so make sure you have done them right.
- Lay the model flat. Let the flap follow the crease and sit in the middle of the diamond.
- Create another tip. Fold the top two corners of the "flap" in towards the center twice as if making the Classic Airplane.
- Make another "X" crease. Align the edges of the created tip with the center of the model. Repeat for other edge and unfold. This will again create an "X" assisting in the next fold.
- Pinch the tip of the "airplane nozzle". Allow the paper to follow the creases while you bringing the tip upright.
- Align to singular edge. Fold the tip down and tuck half of the diamond behind the model. From the side your model should look like a big mountain with a little one overlapped behind.
- Make a tail. Take the big mountain and fold it over onto the model so that it aligns with the small mountain behind it. The direction of this step will determine if you have feet or not. You have folded wrong if the bigger "mountain" covers the lesser.
- Create the head. Slightly open the top of the model, push the tip forward, and then flatten the model once again. The location of this fold can be adjust for different head sizes.
- Repeat this process similarly by opening the tip again, folding downwards, and then flattening. To round off beak repeat one more time this time tucking into the model.
- Fold down the two flaps on the front and back of the model to create the wings. If the wings are missing go back to step 7 and rework.
- Extend the feet. Flatten the bottom of the model, fold out the smaller flap, and then flatten the model. Very similar fold as step 16 but is more difficult as there are more layers to worry about.
- Finish the Parrot. Repeating the previous step one more time, adjust the desired length of the claws to fit your finger or desired perch.
EditTips
- Due to the folding it may be difficult to reuse this dollar bill. Using a credit card or the dull side of a knife can straighten it out again for vending machine/purchasing purposes.
- The ideal paper size ratio for this model is 2 to 1.However, as in the case of a dollar bill, a ratio of up to 2.35 to 1 can be used.
EditWarnings
- This is a difficult model, take your time, and don't be discouraged by mistakes.
- Be cautious when folding. A too fast or careless fold can destroy your dollar bill.
source How to of the Day http://ift.tt/2ok3IVz
Aucun commentaire:
Enregistrer un commentaire