How to Remove Tree Stumps

If you recently cut down a tree in your yard, you have several options for getting rid of the unsightly stump. You can dig it up by hand, grind it, burn it, or use a chemical stump remover. Choose the method that works best for the root system you're dealing with. See Step 1 and beyond to learn how to remove your tree stump.

Steps

Digging Out the Stump

1. Dig around the roots. Use a shovel to dig next to the stump, exposing the roots underneath the surrounding dirt. Move around the circumference of the stump and continue digging until you've exposed all of the largest roots around the tree. Dig deep on either side of the roots to expose them as much as possible.
   
   
   
   
   
   
   
   
   
   • If the roots seem very large and deep, and it's difficult to completely uncover them, you might want to consider a different root removal method. This method works much better when you're able to uncover the roots almost to their tips.
   
   
   
   


2. Cut up the roots. Depending on the size of the roots, use loppers or a root saw to cut them into pieces. Cut them into manageable pieces and pull what you can out of the ground. Toss them into a pile as you go, clearing away as much of the root system as possible.
   
   
   
   
   
   
   
   
   
   • Using an ax to cut the roots is possible, but not recommended because it can shatter dangerously if it strikes a rock, and it will usually end up stuck between roots if they are not completely exposed.
   
   
   
   


3. Pull out the roots. Use a grub hoe to wrench the remaining embedded roots out of the ground to their very tips. If you need to make more cuts as you go, do so - it will make pulling them out of the ground easier. Keep going until you've removed all of the major roots, then go back and pull out anything that's left.
   
   
   
   
   
   
   


4. Remove the stump. After all or most of the roots have been processes, you should be able to easily dislodge the stump. You may need to use the shovel to dig underneath the stump and cut a few more roots under it before you can get it out.
   
   
   
   
   
   
   
   
   
   • Now that all the wood has been removed, you can chop it up and add it to your compost pile.
   
   
   
   


5. Fill in the hole. The final step is to fill up the hole with loam or sawdust. If you fail to do so, the ground around the hole will collapse and you'll have a large dent at that spot in your yard. As the loam or sawdust settles, the ground will sink in a bit, so you may need to keep adding material to the area every few months before the ground will stay flat.
   
   
   
   
   
   
   

Grinding the Stump

1. Locate a stump grinder. This machine grinds up stumps and their root systems to a depth of about a foot beneath the ground. Stump grinders can be rented from machine rental houses by the day.^[1] If you'd prefer not to operate the machine yourself, you can hire someone to come to your property with a stump grinder and do the job for you.
   
   
   
   
   
   
   
   
   
   • You should wear gloves, goggles and ear protectors if you plan on operating the machine yourself.
   
   
   
   


2. Position it over the stump and start grinding. Following the manufacturer's instructions, position the stump grinder and turn it on. It will grind the stump's surface and work its way down into the ground to grind up the roots. You'll need to move the stump grinder around the circumference of the stump in order to take care of the areal roots as well.
   
   
   
   
   
   
   


3. Shovel out the grindings. The ground will repair itself more quickly if you remove the ground up wood. Shovel it out and put it in your compost pile or dispose of it in another way.
   
   
   
   
   
   
   


4. Fill the hole. Replace the grindings with loam or sawdust to fill the hole. Continue adding matter to the area as it depresses over time.^[2]
   
   
   
   
   
   
   

Burning the Stump

1. Build a wood fire on top of the stump. It might be handy to use the chopped-up tree you just cut down as fuel to burn a fire on top of the stop. Lay out the wood on top of the stump. Surround the stump with more wood, so that the stump will be at the center of the fire.
   
   
   
   
   
   
   


2. Keep the fire burning. It will take several hours to burn the stump. Keep adding more wood so that the fire stays large and hot. Keep it burning for as long as it takes for the stump to alight and burn down to the ground.
   
   
   
   
   
   
   


3. Shovel out the ash. After the stump has burned, shovel the ash out of the hole and discard it.
   
   
   
   
   
   
   


4. Fill the hole. Replace the ash with loam or sawdust. Keep adding matter to the area when it sinks every few months.
   
   
   
   
   
   
   

Using a Chemical Stump Remover

1. Drill holes in the stump. Use a drill with a large bit to drill a series of holes in the top of the stump. The stump will absorb the chemicals through these holes, so make sure you space them evenly.
   
   
   
   
   
   
   


2. Apply the stump remover. Most stump removers are composed of powdered potassium nitrate, which reacts with the wood to soften and rot more quickly. Check the directions on the package and apply the stump remover to the stump as instructed.^[3]
   
   
   
   
   
   
   


3. Keep children and animals away from the stump. If the stump removal powder is ingested, it can cause harm to kids and pets, so make sure they don't go near it.
   
   
   
   
   
   
   


4. Monitor the stump. It should begin to soften and rot within a few weeks. When you deem it to be soft enough to easily remove, it's time to finish the job.
   
   
   
   
   
   
   


5. Chop it up. Use an ax or a shovel to chop up the softened stump. Remove pieces as you chop them away. Keep going until you've leveled the stump.


6. Burn the rest. Build a fire over the remaining softened wood and let it burn all the way down. This way you'll remove what's left of the stump and its roots.
   
   
   
   
   
   
   


7. Replace the ashes with loam. Dig out what's left after the fire has burned and discard it. Fill up the hole with loam or another filler, like sawdust. Keep adding more material over the next few months until the ground stays leveled.
   
   
   
   
   
   
   

Tips

• Have someone help you, and don't rush the job.


• Try cutting as many roots as possible before trying to rock the tree and loosen the stump from the ground.


• Plan each step carefully.


• Think about what could go wrong before it happens.


• If you leave a very long portion of the lower trunk, you can use a rope tied to the top to apply the leveraging force by hand. Use a rocking motion to work the stump loose.


• Make sure your tools are sharp and in good condition.


• If all else fails, call a professional.


• If this process doesn't work, fell the trunk close to the base above the stump, and burn the stump.

Warnings

• Wear protective eye wear.


• Wear gloves.


• Don't work if you are over tired.


• Drink plenty of water if you are working in hot weather.


• Be careful using sharp objects, such as the axe, and chainsaw.

Things You'll Need

• Protective Eyewear


• Gloves


• Limbing or pruning saw


• Chainsaw (optional)


• Ax


• Shovel (and trowel when working on shrubs)


• Stump grinder


• Chemical stump remover

Related wikiHows

• How to Prune Tecoma stans


• How to Cut a Limb from a Tree


• How to Select a Ficus benjamina


• How to Understand the Characteristics of Cacti


• How to Dig up Tree Roots

Sources and Citations

Cite error: <ref> tags exist, but no <references/> tag was found

source How to of the Day http://ift.tt/154Puyn